CS7.1 Parts List

Electronics and Enclosure Parts	The Amazon links below are affiliate links which help to support this project.
12v Jack	https://amzn.to/3n67qXa https://amzn.to/3n9MMW3
12mm Push button switch	https://amzn.to/3n6LuLu https://amzn.to/447cNps
12v motor dimmer PWM (led dimmer)	https://amzn.to/3Vfk4ji
Arduino Uno R3 (Genuine Arduino recommended)	https://amzn.to/41MlUL2 https://amzn.to/42ilqw3 https://amzn.to/40Alq9n
CNC Expansion Shield	https://amzn.to/3OAztb1 https://amzn.to/4239Q7R https://amzn.to/3Lc8nFp https://amzn.to/453iR2u
(2) TCM 2209 V2.0 Stepper Motor Driver	https://amzn.to/3mYRoyp
(7) 2-pin jumpers	https://amzn.to/3oOtDcz
40mm 12v Enclosure Fan	https://amzn.to/3L8RhrK
12v 5amp Power supply	https://amzn.to/3VfkOVC https://amzn.to/3oFcvGd
1.2K Ohm Resistor This is to reduce the voltage range on the light ring dimmer.	https://amzn.to/3NiFxpp https://amzn.to/3Lb1ILs - Book of resistors as seen in the build series (better value).
Classifier and Sorter Parts
USB Camera Module (ELP VGA Super Mini VGA USB Camera Module with 100degree Lens)	https://amzn.to/40GxF4d https://amzn.to/3V8l2h6 https://www.aliexpress.us/item/2255800336352705.html?pdp_ext_f=%7B%22sku_id%22%3A%2210000002666544172%22%7D https://amzn.to/447eGT4 https://www.ebay.com/itm/185377133446
USB Camera (V2) If the camera above is not available, this is a substitue version which can be used. Super Mini USB Camera Module with 110degree Lens	https://amzn.to/3M3YRG1 https://amzn.to/3nHM42z AliExpress - Link1 AliExpress - Link2
40mm Blower Fan 12v with Air Guide It is great if you get them with the air guide. Some of the links to do not have the air guides and you would need to purchase them separately or print your own. I have included links to the stand-alone air guides as well.	With Air Guides https://amzn.to/40F2mGW https://amzn.to/3Au1PNd https://amzn.to/3n7EaPM NO Air Guide https://amzn.to/3oBQyYy https://amzn.to/3n5NiV3 https://amzn.to/40FptB6 Air Guide Only https://amzn.to/3n5VHb8 https://amzn.to/3n6a536
LED Strip 6.56ft/4000k (PAUTIX COB LED Strip) Dimmable 5V	https://amzn.to/423bqGP
(2) NEMA 17 Motors (1.5a)	https://amzn.to/3V7aTB8 https://amzn.to/3LxXKxO
Nema17 motor cables	https://amzn.to/3Avaorb
(2) 5mm ID Flange Shaft Coupling	https://amzn.to/445x66P https://amzn.to/443l1z7
6.35mm (.25in) x 22mm (.88in) extension spring	https://amzn.to/443EkYW You can order the spring by itself, but cheaper to buy the spring kit and have extra springs when you need them.
6mm ID, 19mm OD Bearings	https://amzn.to/3ArJ7pL Recommended have 2 for each caliber you plan on sorting.
(2) Homing Sensors	https://amzn.to/3AxlYC6 https://amzn.to/3n6dYoB
Inductive Proximity Sensor (8mm, 3wire NO) Part Number: PR08-2DN	https://amzn.to/3HdRLf2 https://amzn.to/3AtqBNN https://amzn.to/3LcVN8C
M8 x 1.0mm Threaded Insert (for proximity to screw into). Do not use M8x1.25mm as it is a different thread pitch. Alternatively you can use thread reducing nut if insert is unavailable.	Recommended Option M8 x 1.0 Threaded Insert Alternative Options https://www.harfington.com/products/p-1334884 https://amzn.to/3Lwertv https://amzn.to/3HfxXId https://www.fittings.space/gsm26-m8x10-m10x10m https://www.ebay.com/itm/201781023109 https://www.ebay.com/itm/115667535076 https://www.ebay.com/itm/234705490225
M6 x 80mm Socket Head Cap Screw	https://amzn.to/3Vamtf1
M6 Nuts. Locknuts are ok too: You can use any m6 nuts, or you can use the locking system provided by Karl in the community contributions folder.	https://amzn.to/3V6BEFY https://amzn.to/41G6dVk
M6 Cap Screws (10) M6x25 (Mounts) (1) M6x16 (TC Stop) (1) M6x30 (TC Axle)	https://amzn.to/40CohOV
M3, M5 Screw assortment (8) M3x12 (motor mounting) (1) M3x15 (Feed Tube Set Screw) (2) M3x15 (Sorter Pipe Bracket Set Screws) (1) M3 x 20 (Tension spring mount) (8) M3 x 12 (motor shaft flange coupling) (1) M3x 15 Camera Set Screw (1) M3x 25 Drop Nozzle Set Screw (4) M3x7-10 Homing sensor screws (2) M5x 20 (sorter base mount)	https://amzn.to/41ZqPI5
M2 Screws Used for attaching the camera blower fan. (3) 8 screws (1) 12mm screw	https://amzn.to/3oJfUE5
M3 x 30mm screw 1 is needed for drop nozzle retainer.	https://amzn.to/3ndUf6m
Rubber O-ring 16 x 1.5 (16mmID, 19MM OD)	https://amzn.to/3Nc9Yh5 https://amzn.to/3V6DqXM
Optional Parts, Tools and Accessories
Lever Wire Nut Connectors	https://amzn.to/3Lb4ZKK
Threaded Inserts Currently these are only used for the quick change lightshade which requires an M3 insert.	https://amzn.to/3Vbi5MY https://amzn.to/3Ngs1CL https://amzn.to/3AtUNrR
DuPont Crimping Tool (tool only)	https://amzn.to/3Av0OEL https://amzn.to/3Au4CGb
Dupont Crimping Kits (tool + connectors)	https://amzn.to/3V80kOi https://amzn.to/40CpKEV
Dupont Connectors	https://amzn.to/3Lz79FK
Jumper Wire Kit (a must have for Arduino projects)	https://amzn.to/41HgAZ7
Basic Multimeter	https://amzn.to/3n316jb https://amzn.to/4227Zjq
Computers
Miniform Factor Computers (Tested & Verified) These computers have been tested and are known to work with the AI Headstamp Sorter software. For more information, it is highly recommended to reach out to the community on discord to get feedback and further recommendations	Beelink SER5 Mini Computer Beelink SER5 Pro
Miniform Factor Computers (Unverified) These computers "should" work but have not been verified by the community yet but are low cost and appear to meet the necessary requirements to function properly with the AI Headstamp Sorter Software.	Beelink Ryzen 7 5800 Beelink SER5 MINIPC Beelink SER6 Ryzen 7 Beelink SER6 Ryzen 7 Pro